← 返回资讯
2026-11-15约 27 分钟阅读责任主体:芯芸达

A Sensor Responds in 100 ms. What Does That Timing Mean?

Compare sensor response thresholds, step amplitude, assembly and output timing. Recompute fictional t63/t90 responses and read actual WIKA and Sensirion table conditions.

Two sensor quotations both advertise a response time of 100 ms. One defines the time to reach about 63% of a step change. The other defines the time to reach 90%. The identical headline numbers describe different responses.

Before comparing suppliers, identify the measured parameter, response threshold, test conditions and point at which the clock starts. Then establish whether the figure concerns the sensing element, an assembled probe or the value delivered to the control system. Those details determine what the buyer can conclude from the timing claim.

The worked examples below describe fictional first-order responses. They provide arithmetic a reader can inspect alongside the supplier's actual measurements and specification.

Measure a fraction of the step change

A response-time test begins with an identified change in the input and observes how the output approaches its new value. The threshold should refer to a stated fraction of that change.

For a fictional temperature step from 20°C to 70°C, the total change is 50 K. Reaching 90% of the change means reaching `20 + 0.9 × 50 = 65°C`. The initial value belongs in the calculation.

The same reasoning applies to a falling step. A change from 70°C to 20°C reaches 90% of its 50 K decrease at 25°C. Record the direction and the method used to create and observe the step.

WIKA's response-time explanation discusses several percentage thresholds and compares thermometers with different thermowell arrangements. That provides a practical example of why the threshold and assembly belong with the number. WIKA temperature response explanation

Use a first-order model with its assumptions visible

For a simple first-order response with no pure delay, the following expression gives the fraction of the final step reached at time `t`.

`f(t) = 1 − exp(−t/τ)`

The time constant `τ` sets the rate of approach in this model. At `t = τ`, the response has reached approximately 63.2% of the step. Solving for a chosen fraction `f` gives the corresponding threshold time.

`t_f = −τ × ln(1 − f)`

The model assumes a particular response shape. A real probe, filter or installed system needs its own measured response and an appropriate model assessment.

Step fraction reachedTime in the fictional first-order model
50%Approximately 0.693 × τ
63.2%, roundedApproximately 1 × τ
90%Approximately 2.303 × τ
95%Approximately 2.996 × τ
99%Approximately 4.605 × τ

The response approaches the final value asymptotically in this model. At five time constants, it has reached approximately 99.33% of the step. An acceptance procedure therefore needs a finite threshold or tolerance band and, where relevant, a required time inside that band.

Put the two 100 ms quotations on one basis

Consider two fictional sensors that both follow the model above. Supplier A's 100 ms figure is its time constant. Supplier B's 100 ms figure is its 90% response time.

For A, the modeled time to reach 90% is `100 × ln(10)`, approximately 230.3 ms. For B, the modeled time constant is `100/ln(10)`, approximately 43.4 ms.

Fictional quotationDefined headlineCalculated time constantCalculated 90% time
Aτ = 100 ms100 msApproximately 230.3 ms
Bt90 = 100 msApproximately 43.4 ms100 ms

These conversions require the stated first-order shape. For an actual procurement comparison, ask for a response curve or test result that supports using the conversion for the proposed configuration.

For fictional sensor B and the 20°C-to-70°C step, the model reaches 65°C after 100 ms and 69.5°C after 200 ms. Those values show why reaching a named fraction and settling within an application's permissible error can be different requirements.

State the allowable error in the relevant unit and identify the period over which the output must stay within it. A temperature tolerance, a percentage of step amplitude and a percentage of full scale can set different thresholds.

Preserve the parameter and test medium

A device can measure several quantities with different response characteristics. Retain the actual parameter named by each table row.

Sensirion's SHT85 product page lists a humidity response time of 8 seconds at a τ63% threshold. Its linked datasheet identifies the humidity-step definition and conditions of 25°C and 1 m/s airflow. The same datasheet gives a separate temperature-response entry and explains that application design affects the response. Sensirion SHT85 product information, SHT85 datasheet

Keep the humidity label, threshold and airflow condition with that 8-second value when summarizing the source. The superscript footnote attached to the value also needs to survive extraction, particularly when converting a PDF table into English website copy.

A temperature probe tested in flowing water and a probe operating in relatively still air encounter different heat-transfer conditions. A buyer needs the applicable test medium, flow or agitation, immersion and mounting information to assess the relevance of the supplied result.

WIKA's TR10-B data sheet illustrates the assembly distinction with separate tables for measuring inserts and complete instruments with thermowells. Its published example page identifies water as the medium and approximately 125 mm immersion depth. Preserve the actual table and configuration when using its example values. WIKA TR10-B data sheet, page 17

Trace the value to the required output

The buyer may need a usable value at a controller, while a datasheet figure describes the sensing element. List the stages between them.

The probe's thermal behavior, transmitter conversion, configured filtering, sampling interval, communication and application processing can all affect when the buyer receives a usable result. Establish which stages were included in the quoted test.

A regular update interval describes how often an output is refreshed. The underlying sensor can still approach a changed input over several updates. Similarly, an acquisition system can introduce a delay between measuring a value and presenting it to a recipient.

For another fictional calculation, give sensor B a pure delay of 20 ms before the first-order response begins. Its time constant remains approximately 43.4 ms. The modeled 90% time from the original input step becomes 120 ms.

This example specifies both the delay and response shape. A real multi-stage system can require a more detailed model and direct end-to-end measurements. Ask the supplier to identify the measurement point represented by its claim.

Release a timing claim the buyer can evaluate

A short specification table can carry the context that a headline omits.

FieldInformation to retain
Measured parameterTemperature, humidity, pressure or other stated input
Item testedSensing element, probe, thermowell assembly or complete signal chain
Step definitionInitial value, final value, direction and method of applying the change
Response criterionNamed fraction, tolerance band and any settling requirement
Test environmentMedium, flow, immersion, mounting and relevant ambient conditions
Output configurationTransmitter, filter, sampling and communication settings included
Time origin and measurement pointStart event and location at which the output was observed
Supporting recordTest identifier, revision, curve and technical approval

For an RFQ, describe the application decision. A buyer monitoring a slow storage condition may have a different dynamic requirement from one measuring a short process event. Supply the relevant conditions and ask the manufacturer to evaluate the proposed item against that defined requirement.

For English content, keep the threshold and conditions beside the time value. A comparison table can use separate columns for the response criterion and configuration. When an AI summary extracts “100 ms,” the surrounding text should still identify what that number represents.

Xindar's manufacturing content service can structure approved sensor evidence for English supplier research. The technical source owner should approve the response definition and application statement. A measurement-resolution claim needs its own evidence, as explained in the related measurement specification guide.

Questions buyers ask

Are t63 and t90 figures directly comparable?

They represent different fractions of the response. A valid conversion needs an applicable response model or measured curve. State the threshold used by each supplier before comparing the figures.

Where is 90% of a 20°C-to-70°C step?

At 65°C. The calculation adds 90% of the 50 K change to the initial 20°C value. The starting value and step amplitude belong in the test record.

Does a fast digital update rate establish a fast sensor response?

Inspect the physical response and the output timing separately. The update interval identifies the refresh schedule, while the response curve describes how the measured value approaches a changed input.

Can the sensing element's time be used for a thermowell assembly?

Obtain the applicable assembled configuration's evidence. Thermowell geometry, mounting and process conditions affect the path through which the temperature change reaches the sensing element.

What should accompany a response-time requirement?

The measured parameter, proposed assembly, step conditions, acceptance criterion and required output point. Include configuration settings and a test record that lets both parties interpret the result consistently.

Sources and method

Public sources were reviewed on November 14, 2026. WIKA supplies the attributed threshold and thermowell examples. Sensirion supplies the attributed humidity-response definition and conditions. The first-order model, two 100 ms quotations, temperature-step calculations and delayed-response example are fictional editorial teaching material. Product-specific response and application suitability require the relevant configuration and measurement evidence.