Two compression springs have the same stated rate. A buyer selects the smaller one, expecting it to provide the same force in an existing assembly. At the installed length, however, the smaller spring has less compression from its free length and therefore develops a different force under the assumed linear relationship.
The rate describes a change in force per change in deflection. The force at a particular position also depends on the spring's reference length and the operating interval over which the relationship applies. A useful purchasing specification connects those quantities.
For a manufacturer publishing an English catalogue, the working position belongs beside the force claim. It gives a buyer enough information to interpret a rate figure in the intended assembly.
Begin with the unloaded and working lengths
Free length is the spring's unloaded length. A compression spring becomes shorter as it is compressed along its working axis. The difference between the agreed free length and a working length supplies the deflection used in a simple linear calculation.
Lee Spring's catalogue distinguishes free length, spring rate and solid height. Its engineering notes give the compression-spring relationship between rate and deflection for calculating load at a working length. The applicable product and operating range still need to be identified. Lee Spring catalogue, engineering notes and table guides
The illustrative relationship uses force in newtons and length in millimetres.
```text
deflection = free_length - working_length
force = spring_rate × deflection
```
The calculation assumes the stated rate applies over that interval. Keep that assumption attached to the result. Real spring behavior, tolerances and the suitability of an assembly require the applicable engineering information.
Equal rates can produce different installed forces
Consider two fictional linear compression springs. These values are a mathematical fixture, with no claim that either is a purchasable or approved component.
| Quantity | Spring A | Spring B |
|---|---|---|
| Stated rate | 10N/mm | 10N/mm |
| Free length | 50mm | 45mm |
| Illustrative solid height | 18mm | 16mm |
| Installed working length | 40mm | 40mm |
At 40mm, A has 10mm of deflection and the model gives 100N. B has 5mm of deflection and the model gives 50N. The rate figures are identical, while the reference geometry produces different installed forces.
At a second working length of 35mm, the same model gives 150N for A and 100N for B. The 5mm movement between positions increases the force by 50N in each case. That shared change is consistent with their shared rate.
| Working position | A deflection | A modeled force | B deflection | B modeled force |
|---|---|---|---|---|
| 40mm | 10mm | 100N | 5mm | 50N |
| 35mm | 15mm | 150N | 10mm | 100N |
This gives a buyer two useful comparisons. The rate describes how force changes through the stroke. The load-at-length statement describes the modeled force at the actual position.
Specify force at the positions that matter
A spring may need to provide an initial force at installation and a second force at another working position. Record both lengths, the required force or permitted range at each, and the conditions of the measurement.
Lee Spring's custom compression-spring form provides separate fields for rate over a stated interval and two loads at specified positions. It also records free length, solid height and dimensional information. That is a concrete manufacturer example of the additional information behind a rate-only inquiry. Custom compression-spring specification form
For a buyer, two load points can expose an ambiguity that a single rate obscures. A supplier can then evaluate the requested combination using its manufacturing and engineering process.
The governing specification should state how tolerances apply. A nominal rate, a permitted rate range and a load tolerance at a working length are different fields. Preserve the supplier's actual basis and any conditions attached to it.
Keep solid height and the working limit identifiable
Solid height describes the compressed geometry when the coils are brought into contact under the applicable definition. The permitted operating position depends on the specific design and requirements. A catalogue may provide a recommended working height or a force at a stated deflection.
In the fictional example, the difference between the 35mm working length and the illustrative solid height is 17mm for A and 19mm for B. Those distances describe geometry. They provide no independent approval of stress, fatigue, stability or service suitability.
A procurement review should therefore locate the permitted working interval and the conditions supporting it. Extending a straight-line force calculation down to the solid-height figure can go beyond the interval for which the supplier supplied a usable rate.
Keep product-series qualifications with the data. A recommendation for one spring family or a particular fraction of available deflection should retain its original scope when copied into a comparison page.
Read the unit before copying the number
A spring rate combines a force unit and a length unit. N/mm and lbf/in describe the same kind of quantity using different scales. A conversion must change both parts correctly.
A load column also needs an unambiguous force unit. Some legacy catalogues use customary labels whose intended force convention needs to be read in the manufacturer's unit notes. Preserve that convention and clarify ambiguous labels before combining values from different suppliers.
For an English product page, show the unit in the field or column heading and keep it with the value in downloadable data. A list containing only “rate 10” leaves both the physical quantity and scale unresolved.
Also keep working length distinct from travel. A 5mm stroke between two installed positions describes a movement. The absolute lengths at those positions determine the deflections from free length used in the model.
Use a load-at-length acceptance record
The following fields form a proposed purchasing record. They supplement the supplier's governing engineering requirements.
| Record | Information to preserve |
|---|---|
| Component identity | Part, revision, material and applicable specification |
| Reference geometry | Free length and its stated tolerance |
| Working positions | Each required absolute length and the movement between positions |
| Force requirements | Load and tolerance at each relevant position |
| Rate | Unit, stated value and interval to which it applies |
| Operating scope | Agreed working range and application conditions |
| Evidence | Applicable drawing, test method, results and responsible approval |
A controlled review can follow the identified component through the proposed measurement method. Record the actual working length, observed force, test conditions and the acceptance rule agreed for the item.
If the buyer changes the installed position, reopen the affected force requirement. If the supplier changes the free length while preserving a nominal rate, ask how the loads at the required positions are affected. The quotation should identify the combination it offers.
Publish the relationship that the buyer needs
An effective catalogue can present rate, free length and load-at-length information together, with a route to the governing drawing or data sheet. A comparison then has a chance to preserve the conditions behind the headline number.
Avoid assembling a product claim from unrelated maxima. A rate from one variant, a free length from another and a force from a third cannot form an identifiable component record. Variant IDs and document revisions should travel with the figures.
Xindar's manufacturing content service can organize approved spring data into an English buyer-facing structure. The manufacturer's technical owner should approve the component values, operating interval and application statement. Manufacturing content services
An AI visibility review can then inspect whether a sampled answer preserves the rate unit, working length and variant identity. Retain the original answer and its source URLs so any missing condition can be checked. Semvi by Xindar
Frequently asked questions
What does a compression-spring rate describe?
It describes the change in force per unit of deflection over the stated interval. The force at a working position also requires the applicable reference geometry and conditions.
Can springs with the same rate provide different installation forces?
Yes. The fictional example gives different deflections at the same installed length because the free lengths differ.
Is solid height the recommended operating length?
Read the supplier's stated working range for the particular spring. Solid height is a geometric field whose relationship to permitted operation needs its own engineering basis.
What should a quotation preserve?
The component identity, free length, rate and unit, required loads at specified lengths, tolerances and governing documents. Include the application conditions needed for the supplier's review.
